Leading 10 usual forklift accidents ， forklift operation should pay attention to these matters ！.
Leading 10 usual forklift accidents ， forklift operation should pay attention to these matters ！.
Blog Article
Don't underestimate the forklift at work. If the procedure is not good, there will certainly be significant crashes in mins, and there are several accidents involving forklifts.
Case 1: The forklift freight obstructed the chauffeur's sight, and the person ahead could not be discovered, causing a moving accident.
Instance 2: In order to maintain the balance of the forklift when raising hefty goods, the workers used their body weight as the weight, which almost caused casualties.
Instance 3: The width of the forklift freight exceeds the allowable width of the route and holds on the roadside rack, which virtually creates an crash.
Situation 4: Forklift is speeding up and surrender during a turn.
Situation 5: The forklift chauffeur did not observe the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift lifts the employees unlawfully, the forklift driver does not put on the seat belt, the forklift lifter falls and the chauffeur is crushed when the forklift rolls over.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the automobile when it surrendered and was squashed.
Forklift procedure should take notice of these issues ：.
Beginning.
1. Before starting, observe the environments, and after validating that there are no obstacles that hinder the safety and security of driving, beep the horn first and after that start.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be safe prior to starting.
3. When the forklift begins with a load, the chauffeur needs to first verify that the tons is steady and reputable.
4. The begin should be sluggish and stable.
Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be slanted in reverse. .
2. Do not raise the fork too expensive when driving. When entering and leaving the job site or while driving, be careful that there will be no barriers in the sky. When the tons is traveling, the fork has to not be increased too high, which will influence the security of the forklift. .
3. After unloading, the fork ought to be decreased to the typical driving position before driving. .
4. When turning, if there are pedestrians or vehicles nearby, the driving signal should be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly trigger the car to lose side stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the flame and slide, and it is restricted to brake instantly while driving with loads unless there are unique scenarios.
6. When the forklift is running, it has to comply with the website traffic rules in the manufacturing facility and have to keep a specific security range from the car ahead. .
7. When the forklift is running, the lots must remain in the lowest position that does not impede the driving, and the gantry needs to be properly tilted back. The tons shall not be elevated other than when piling or packing. .
8. The height of the tons must not obstruct the chauffeur's sight. In special conditions, when the product impacts the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to activate the ramp, nor to drive across the ramp. .
10. The safe driving speed of the forklift in the factory location is 5 km/h, and it must drive safely at a reduced speed when entering the manufacturing workshop area. .
11. When the forklift is lifted, lifted or driven, it is prohibited for workers to base on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be repaired and reported in a prompt way, and they will never ever run with health problems or conceal them.
loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product ought to protest the rack. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or draw. In special scenarios, security indication need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs Stand-on Electric Pallet Stacker to be noted that the fork pointer ought to not touch various other goods or items. The lots should be supported with marginal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable Stand-on Electric Pallet Stacker very easy placement of the load and extraction of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and harm individuals. .
8. Straining is banned, and it is restricted to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.
Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork frame.
2. Pull the emergency brake deal with to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .
Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage ought to also be examined and the seals must be replaced in time.
Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to prevent the propensity of " totally free turning";.
6. Adding and down the slope must be slow and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they come across large or heavy items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not allowed to raise the goods for cross country driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below conditions.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844